Prepare Fire-Inspector-II Question Answers - Fire-Inspector-II Exam Dumps
Real International Code Council Fire-Inspector-II Exam Questions [Updated 2025]
NEW QUESTION # 25
Given: A nonsprinklered building constructed with protected noncombustible material has a fire-resistive rating of a minimum of 1 hour. What is the most protective type of construction, from the choices below, that meets these parameters?
- A. IIIB
- B. IIA
- C. IIB
- D. VA
Answer: B
Explanation:
Understanding Construction Types
The International Building Code (IBC) Chapter 6 classifies building construction types based on material combustibility and fire resistance.
Type II construction is noncombustible, meaning it is built using materials such as steel or concrete that do not contribute fuel to a fire.
The difference between Type IIA and Type IIB is the level of fire resistance.
2. Fire Resistance Rating Requirement
Type IIA construction requires a minimum 1-hour fire-resistive rating for structural elements, meeting the conditions in the question.
Type IIB, on the other hand, has no minimum fire-resistive rating for structural components, making it less protective than Type IIA.
3. Verification of Other Options
Option B (IIB) - Incorrect, as Type IIB has no fire-resistive rating for its structural elements and does not meet the 1-hour requirement.
Option C (IIIB) - Incorrect, as Type III allows combustible exterior materials and is not entirely noncombustible.
Option D (VA) - Incorrect, as Type V construction is wood-framed and does not meet the requirement for noncombustible materials.
Reference Sources:
International Building Code (IBC) 2021 - Chapter 6 (Types of Construction) NFPA 220: Standard on Types of Building Construction ICC Fire Inspector II Study Guide (2021)
NEW QUESTION # 26
The maximum quantity of liquefied petroleum gas (LP-gas) in containers stored by a dealer awaiting resale, and are at one location in a building that is not open to the public, is __ lb. water capacity.
- A. 1,000
- B. 0
- C. 2,500
- D. 2,000
Answer: D
Explanation:
LP-Gas Storage Limits for Dealers in Non-Public Buildings
According to the International Fire Code (IFC) 2021, Section 6109.9, the maximum allowable quantity of LP- gas in containers stored by a dealer awaiting resale in a building that is not open to the public is 2,000 pounds of water capacity.
This limit is intended to reduce fire and explosion hazards in enclosed spaces while allowing reasonable storage for commercial purposes.
2. Understanding Water Capacity vs. Propane Weight
The water capacity of an LP-gas cylinder refers to the total weight of water the container can hold, not the actual propane content.
The propane content is typically about 42% of the water capacity (i.e., 2,000 lbs. of water capacity is approximately 840 lbs. of propane).
3. Verification of Other Options
Option A (735 lbs.) - Incorrect, as IFC allows a significantly higher storage limit for dealers in non-public buildings.
Option B (1,000 lbs.) - Incorrect, as the actual limit per IFC 6109.9 is 2,000 lbs.
Option D (2,500 lbs.) - Incorrect, as this exceeds the IFC's maximum allowable storage limit.
Reference Sources:
International Fire Code (IFC) 2021 - Section 6109.9 (LP-Gas Storage Limits in Buildings Not Open to the Public) NFPA 58: Liquefied Petroleum Gas Code (LP-Gas Storage and Handling Guidelines) ICC Fire Inspector II Study Guide (2021)
NEW QUESTION # 27
Given: Scheduling inspections should be done to obtain a high level of efficiency. When scheduling inspections at multiple occupancies on the same day, the inspector should:
- A. set limits on the time spent at each occupancy.
- B. select occupancies in the same general area.
- C. select occupancies with historically low violations.
- D. only identify critical violations.
Answer: B
Explanation:
Efficient scheduling minimizes travel time and maximizes inspection coverage, a practical aspect of fire inspection management (not explicitly detailed in the IFC but implied in Section 106.2, Inspections).
Selecting occupancies in the same geographic area (C) reduces travel, allowing more time for thorough inspections. Option A undermines the comprehensive nature of inspections required by IFC Section 106.1.
Option B could compromise inspection quality, not efficiency. Option D focuses on violation history, which doesn't inherently improve scheduling efficiency and may skew priorities. Thus, C is the most logical and IFC-aligned choice.
NEW QUESTION # 28
In a control area where flammable liquid storage containers are in piles, there shall be a minimum of __ in. of clearance between the top of the storage and the deflector or discharge orifices of a sprinkler system.
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
Explanation:
Clearance Requirement for Sprinkler Systems Over Flammable Liquid Storage According to International Fire Code (IFC) 2021, Section 5004.6 and NFPA 30: Flammable and Combustible Liquids Code, Section 16.5.1, there must be a minimum of 18 inches of clearance between the top of flammable liquid storage and the deflector or discharge orifices of a sprinkler system.
This ensures unobstructed sprinkler discharge for effective fire suppression.
2. Why 18 Inches is the Correct Answer
The 18-inch clearance allows sprinklers to operate properly, ensuring water distribution is not blocked by stored materials.
NFPA 13 also mandates an 18-inch minimum clearance for standard storage applications with sprinklers.
3. Verification of Other Options
Option B (24 inches) - Incorrect, as the IFC and NFPA specify 18 inches as the minimum requirement.
Option C (30 inches) - Incorrect, as this exceeds the required minimum clearance.
Option D (36 inches) - Incorrect, as the IFC and NFPA do not require this much clearance.
Reference Sources:
International Fire Code (IFC) 2021 - Section 5004.6 (Sprinkler Clearance Over Flammable Liquid Storage) NFPA 30: Flammable and Combustible Liquids Code - Section 16.5.1 NFPA 13: Standard for the Installation of Sprinkler Systems - Minimum Clearance Requirements ICC Fire Inspector II Study Guide (2021) Thus, the correct and verified answer is: A. 18 inches. #
NEW QUESTION # 29
What fire-resistance rating is required for interior nonbearing walls and partitions in Type IV construction?
- A. 1 hour
- B. 0 hours
- C. 2 hours
- D. 1-1/2 hours
Answer: B
Explanation:
Fire-Resistance Rating for Nonbearing Walls in Type IV Construction
Type IV (Heavy Timber) construction, as defined by the International Building Code (IBC) 2021, Section
602.4, consists of large, solid or laminated wood members.
Interior nonbearing walls and partitions in Type IV construction are not required to have a fire-resistance rating (0 hours) unless they separate different occupancies or are specifically mandated by another code provision.
2. Why Type IV Does Not Require a Rating for Nonbearing Walls
The heavy timber components inherently provide fire resistance due to their large cross-section, which chars on the surface and slows fire penetration.
IBC Table 601 confirms that interior nonbearing walls in Type IV construction do not have a required fire- resistance rating.
3. Verification of Other Options
Option B (1 hour) - Incorrect, as Type IV does not require a 1-hour rating for interior nonbearing walls unless specific conditions apply.
Option C (1-1/2 hours) - Incorrect, as there is no code requirement for this level of rating in Type IV nonbearing walls.
Option D (2 hours) - Incorrect, as Type IV walls are not rated unless separating occupancies.
Reference Sources:
International Building Code (IBC) 2021 - Section 602.4 (Type IV Construction Requirements) IBC Table 601 (Fire-Resistance Ratings for Building Elements) ICC Fire Inspector II Study Guide (2021)
NEW QUESTION # 30
A container in a clean-agent extinguishing system must be refilled or replaced when it shows a loss in original weight of more than five percent, or a loss in original pressure of more than ___ percent.
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
Explanation:
A container in a clean-agent extinguishing system must be refilled or replaced if it experiences a loss of more than 5% of its original weight or a loss in original pressure of more than 3%. This requirement ensures the system maintains sufficient agent concentration for fire suppression.
Reference to Fire Inspector Documentation:
1. NFPA 2001 - Standard on Clean Agent Fire Extinguishing Systems (2022 Edition) NFPA 2001, Section 7.3.2.1 states that a container must be refilled or replaced if the weight loss exceeds 5% or the pressure loss exceeds 3% from the original fill pressure.
These limits are set to maintain system effectiveness and ensure that a clean-agent system can properly discharge in case of a fire.
2. 2021 International Fire Code (IFC) - Chapter 9 (Fire Protection Systems) IFC 904.10 requires that clean-agent systems be maintained per NFPA 2001 to ensure reliability.
Detailed Explanation of Answer Choices:
Option A (Correct): 3% pressure loss is the correct threshold beyond which a container must be replaced or refilled.
Option B (Incorrect): While 5% is correct for weight loss, it is not the correct value for pressure loss.
Option C (Incorrect): A 10% pressure loss is too high and would compromise system performance before reaching the replacement threshold.
Option D (Incorrect): 12% is well beyond the acceptable loss limit and would pose a significant safety risk.
Thus, the correct and verified answer is: A. 3
NEW QUESTION # 31
A Type I handrail that is not circular shall have a minimum perimeter dimension of ___ inches.
- A. 0
- B. 1.25
- C. 1
- D. 6.25
Answer: D
Explanation:
According to the 2021 International Fire Code (IFC) and the International Building Code (IBC) Section
1014.3, handrails are categorized into Type I and Type II based on their shape and size requirements.
Type I handrails refer to those that are not circular in shape but still comply with graspability requirements.
IBC Section 1014.3.1 states that:
If a handrail is not circular, it must have a perimeter dimension between 4 inches (minimum) and 6.25 inches (maximum).
The cross-section of such a handrail should provide an adequate grasping surface.
NEW QUESTION # 32
Given: A code official permits a sprinkler system to substitute for a required second exit from a small basement.
How long must records related to this decision be maintained by the code official?
- A. Three years
- B. Five years
- C. For as long as the building and the condition exist
- D. Until the building is sold
Answer: C
Explanation:
Retention of Fire Code-Related Records
According to the International Fire Code (IFC) 2021, Section 104.6, records related to code enforcement decisions, including modifications or substitutions (such as a sprinkler system replacing a second exit), must be retained for as long as the building and the condition exist.
This ensures that future inspections, property owners, and authorities can verify past decisions and compliance history.
2. Why the Records Must Be Retained Permanently
Modifications that impact life safety (such as exit requirements) must remain on record for the lifetime of the building to ensure ongoing compliance and safety.
If the condition (sprinkler substitution for an exit) still exists, any future inspector or building official must be able to verify the original approval and rationale.
3. Verification of Other Options
Option A (Five years) - Incorrect, as fire code modifications must remain on record permanently if they affect egress or fire protection systems.
Option B (Three years) - Incorrect, as this timeframe applies to temporary inspection reports, not major code modifications.
Option C (Until the building is sold) - Incorrect, as ownership changes do not affect the need for record retention on fire safety decisions.
Reference Sources:
International Fire Code (IFC) 2021 - Section 104.6 (Fire Code Record Retention Requirements) NFPA 1: Fire Code (Retention of Code-Related Decisions) ICC Fire Inspector II Study Guide (2021) Thus, the correct and verified answer is: D. For as long as the building and the condition exist. #
NEW QUESTION # 33
Flammable medical gas supply cylinders located inside of a building must be stored in a separate room of not less than __ fire-resistive construction when exceeding 200 cu. ft.
- A. 1-hour
- B. 2-hour
- C. 1/2-hour
- D. 3-hour
Answer: B
Explanation:
The storage of flammable medical gas supply cylinders inside a building is regulated by 2021 International Fire Code (IFC) Section 5306 - Medical Gas Systems.
IFC Section 5306.2.1 - Storage of More Than 200 Cubic Feet of Medical Gases:
When the quantity of flammable medical gas exceeds 200 cubic feet, it must be stored in a separate room with a minimum 2-hour fire-resistance rating.
The room must also comply with ventilation and explosion control requirements per NFPA 99 (Healthcare Facilities Code).
Why Other Options Are Incorrect?
A: 1/2-hour - Insufficient fire resistance for high-risk gas storage.
B: 1-hour - Does not meet the minimum 2-hour requirement set by the IFC.
D: 3-hour - Exceeds the minimum required by code; the correct requirement is 2-hour fire-resistive construction.
NEW QUESTION # 34
In the fire code, ABS plastics are designated as ___ plastic materials.
- A. Commodity Class III
- B. Group B
- C. Group A
- D. Group C
Answer: C
Explanation:
IFC Section 2303.7 classifies ABS (acrylonitrile butadiene styrene) plastics as Group A (high-hazard) due to their flammability and smoke production, per NFPA 13. Options B and C are less hazardous, D is a commodity class, not a plastic group. Thus, A is correct.
NEW QUESTION # 35
Hazardous occupancies involved in the manufacturing of organic coatings:
- A. require only an automatic fire alarm system.
- B. require only a manual fire alarm system.
- C. require both manual and automatic fire alarm systems.
- D. do not require a fire alarm system.
Answer: C
Explanation:
Hazardous occupancies involved in organic coatings manufacturing are classified as Group H-2 or H-3 occupancies under the 2021 IFC. These facilities involve highly flammable materials, requiring both manual and automatic fire alarm systems for safety.
IFC 2021, Section 415.7 - Organic Coatings Manufacturing:
Requires that automatic fire alarm and manual fire alarm systems be installed due to the high risk of fire and explosion in these facilities.
IFC 907.2.4 - Fire Alarm Systems for Group H Occupancies:
Specifies that Group H (high-hazard) occupancies must have both manual and automatic fire alarm systems.
The automatic fire alarm system ensures immediate detection, while the manual system allows for human activation in case of emergencies.
Why Other Options Are Incorrect?
A: Do not require a fire alarm system.
Incorrect, as all high-hazard occupancies require fire alarm systems.
B: Require only a manual fire alarm system.
Incorrect, as automatic detection is also required due to high fire risk.
C: Require only an automatic fire alarm system.
Incorrect, as manual activation is necessary for early intervention.
NEW QUESTION # 36
A building occupied for aerosol storage shall be classified as which of the following occupancy classifications?
- A. High-hazard Group H-3
- B. Group S-1
- C. High-hazard Group H-2
- D. High-hazard Group H
Answer: D
Explanation:
IFC Section 3804.1 classifies aerosol storage as Group H (high-hazard) if flammable, fitting option A.
Options B and C are subgroups (H-2, H-3), while D (Group S-1) is for moderate-hazard storage, not applicable. This is consistent with the study guide's occupancy classifications.
References: Fire Inspector II Study Guide, IFC Section 3804.1.
NEW QUESTION # 37
Two tents which each have an area of 20,000 sq. ft. shall be separated from each other by a distance of not less than:
- A. 0 ft. (no separation is required).
- B. 20 ft.
- C. 25 ft.
- D. 10 ft.
Answer: B
Explanation:
IFC Section 3103.8.2 (Separation of Temporary Tents) requires tents larger than 15,000 sq. ft. to be separated by at least 20 feet to prevent fire spread, unless connected by a corridor meeting specific requirements (not indicated here). Each tent at 20,000 sq. ft. exceeds this threshold, necessitating 20 feet of separation. Option A (0 ft.) applies only to smaller tents, B (10 ft.) is insufficient, and D (25 ft.) exceeds the minimum. Thus, C is correct.
NEW QUESTION # 38
Existing elevators in a four-story office building which are intended for use by emergency personnel for fire- fighting or rescue purposes must comply with which of the following standards?
- A. UL 803
- B. NFPA 70
- C. ASME A17.3
- D. ASME A17.1
Answer: D
Explanation:
Reference to Elevator Safety and Firefighter Use:
ASME A17.1 (Safety Code for Elevators and Escalators) establishes the safety requirements for elevators, including those designated for firefighter and emergency personnel use.
The International Fire Code (IFC) and NFPA 101 (Life Safety Code) both reference ASME A17.1 when addressing elevator safety and firefighter access.
Firefighter Access and Operation Requirements:
ASME A17.1, Section 2.27 covers Firefighter Emergency Operations (FEO), which includes:
Phase I Operation (Automatic recall of elevators to a designated floor upon activation of fire alarms).
Phase II Operation (Manual override by firefighters for rescue and suppression operations).
IFC 607.1 (2021 Edition) mandates that fire service access elevators comply with ASME A17.1 for firefighter use in high-rise and multi-story buildings.
Clarification of Incorrect Answer Choices:
A: UL 803 # Incorrect
UL 803 is not related to elevator fire safety; it pertains to electrical control panels for industrial applications.
B: NFPA 70 (National Electrical Code) # Incorrect
While NFPA 70 covers electrical wiring and circuits, it does not specifically regulate elevator emergency operations.
D: ASME A17.3 # Incorrect
ASME A17.3 is the Safety Code for Existing Elevators and Escalators, which applies to retrofits and upgrades, but ASME A17.1 is the primary code for operational and emergency use elevators.
Conclusion:
The correct and verified answer is C (ASME A17.1) because it specifically outlines the requirements for firefighter and emergency personnel elevator use, ensuring compliance with the IFC and NFPA codes.
NEW QUESTION # 39
Multiple smoke alarms installed within individual guest rooms of a hotel must comply with which of the following requirements?
- A. Their batteries must be checked every six months.
- B. They must automatically sound a fire alarm throughout the hotel.
- C. They must be interconnected so that one alarm will activate all alarms within the guest rooms.
- D. They must initiate an automatic fire suppression or sprinkler system.
Answer: C
Explanation:
Smoke alarm requirements for individual guest rooms in hotels are specified in the 2021 International Fire Code (IFC) Section 907.2.11.3 and NFPA 72 (National Fire Alarm and Signaling Code).
IFC 907.2.11.3 - Smoke Alarms in Group R-1 Occupancies (Hotels and Motels):
Requires smoke alarms in sleeping areas to be interconnected so that when one alarm is activated, it will trigger all alarms within the guest room or suite.
This ensures that occupants in different areas of the same guest room are alerted simultaneously to fire hazards.
Why Other Options Are Incorrect?
A: Their batteries must be checked every six months.
The IFC and NFPA 72 require smoke alarm batteries to be checked, but they do not mandate a six-month inspection schedule.
B: They must automatically sound a fire alarm throughout the hotel.
Smoke alarms within an individual guest room do not have to activate the entire hotel's fire alarm system.
C: They must initiate an automatic fire suppression or sprinkler system.
Smoke alarms are designed for early detection and warning, not for activating fire suppression systems.
NEW QUESTION # 40
A code official may allow the occupant load of a building or room to exceed that specified in the building code if additional exit facilities are provided, all other egress requirements are met, and the maximum occupancy does not exceed one occupant per sq. ft. of occupiable floor area.
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
Explanation:
A code official may allow the occupant load to exceed the building code requirements if additional exit facilities are provided, all egress requirements are met, and the maximum occupancy does not exceed one occupant per 10 sq. ft. of occupiable floor area.
Reference to Fire Inspector Documentation:
1. 2021 International Building Code (IBC) - Table 1004.5 (Occupant Load Factor) The minimum safe occupancy load factor is 10 sq. ft. per occupant, meaning no space can have more than 1 person per 10 sq. ft.
Fire code officials can approve increased occupancy only if extra exits are provided, ensuring compliance with egress and fire safety rules.
2. 2021 International Fire Code (IFC) - Section 1004.2 (Increased Occupant Load Allowance) Allows for an increased occupant load only if additional exits and egress requirements are met but never beyond 1 person per 10 sq. ft.
Detailed Explanation of Answer Choices:
Option A (Incorrect): 1 occupant per 3 sq. ft. is too high and would violate egress safety regulations.
Option B (Incorrect): 1 occupant per 5 sq. ft. still exceeds safety limits.
Option C (Incorrect): 1 occupant per 7 sq. ft. is not the minimum required standard.
Option D (Correct): 1 occupant per 10 sq. ft. is the minimum limit for allowing an increased occupant load under IFC 1004.2 and IBC Table 1004.5.
Thus, the correct and verified answer is: D. 10.
NEW QUESTION # 41
Panic hardware is required on exit doors serving an occupant load of __ or more in a Group __ Occupancy
- A. 50; A
- B. 10; A
- C. 100; F
- D. 50; M
Answer: A
Explanation:
The requirement for panic hardware on exit doors is specified in 2021 IFC Section 1010.2.9 - Panic and Fire Exit Hardware.
IFC Section 1010.2.9.1 - Where Panic Hardware is Required:
Panic hardware is required for Group A (Assembly) occupancies when the occupant load is 50 or more.
It is also required in certain Group E (Educational) and Group R-1 (Hotels and Dormitories) occupancies under specific conditions.
Why Other Options Are Incorrect?
A: 10; A - The threshold for panic hardware in Group A occupancies is 50, not 10.
C: 50; M - Group M (Mercantile) does not require panic hardware unless specifically required by another section of the code.
D: 100; F - Panic hardware is not required in Group F (Factory) occupancies at 100 occupants; the threshold applies primarily to Group A.
NEW QUESTION # 42
......
Fire-Inspector-II Exam Dumps Pass with Updated 2025: https://www.actual4exams.com/Fire-Inspector-II-valid-dump.html
Free Fire-Inspector-II Exam Dumps to Pass Exam Easily: https://drive.google.com/open?id=1fqd_5AZ-3DCoAImMeV0ltsbYWXYq9A4g