CheckPoint 156-835 Cert Guide PDF 100% Cover Real Exam Questions
Pass 156-835 Exam - Real Questions and Answers
NEW QUESTION # 17
For a VSX configuration - Which statement is wrong?
- A. Each Appliance owns different Virtual Systems
- B. All Virtual Systems exist on the SMO
- C. All Virtual Systems exist on all Appliances
- D. VSX configuration is the same on all Appliances within the same Security Group
Answer: B
NEW QUESTION # 18
There's a 23800 appliance with quad NIC in slot 5. What would be the name of port 3 on this NIC?
- A. ethBP3-05
- B. ethsBP5-03
- C. ethsBP3-05
- D. ethsBP-05
Answer: B
NEW QUESTION # 19
Which command will be used in order to restart Orchestrator service only?
- A. reboot
- B. cpstop; cpstart
- C. orchd restart
- D. service orchestrator restart
Answer: D
NEW QUESTION # 20
What is the Orchestrator?
- A. Network Switch
- B. None of above
- C. Load balancer
- D. Manager of compute and network resources, load balancer and network switch
Answer: B
NEW QUESTION # 21
What kinds of transceivers are supported on Orchestrator MHO-140?
- A. SFP, SFP+, QSFP, QSFP28
- B. SFP, QSFP, QSFP28
- C. SFP+, SFP28, QSFP
- D. SFP, SFP+, SFP28
Answer: A
NEW QUESTION # 22
What is the default Distribution mode?
- A. User
- B. Manual-General
- C. Network
- D. Auto-topology
Answer: D
Explanation:
In Check Point firewall, the default Distribution mode is Auto-topology. Auto-topology uses the built-in algorithm to automatically determine the best way to distribute the traffic across the firewall cluster, based on the topology of the network and the current load on the cluster members.
Auto-topology takes into account the available bandwidth and the CPU utilization of each cluster member, and then makes decisions on how to distribute the traffic across the cluster in real-time. It is a dynamic and adaptive mode that ensures the best use of the available resources and the highest level of performance.
NEW QUESTION # 23
Orchestrator should be defined in SmartConsole as:
- A. Security Gateway
- B. Check Point host
- C. Host
- D. Orchestrator is not defined in SmartConsole
Answer: D
NEW QUESTION # 24
What does the lldpctl command do?
- A. Show all devices discovered by LLDP protocol on downlink ports
- B. Discover orchestrators
- C. Show all devices discovered by LLDP protocol on all ports
- D. Show all devices discovered by LLDP protocol on uplink ports
Answer: C
NEW QUESTION # 25
What is an uplink interface used for?
- A. To connect appliances to customer's infrastructure
- B. To connect in between appliances
- C. To connect in between Orchestrators
- D. To connect Orchestrators to customer's infrastructure
Answer: A
NEW QUESTION # 26
What command should be used for collecting diagnostic information about the orchestrator?
- A. asg pert -v
- B. orch_info
- C. cpview
- D. cpinfo
Answer: B
NEW QUESTION # 27
What command will be used for updating fwkern.conf file on all Appliances within Security Group?
- A. g_update_conf_file
- B. g_all update_conf_file
- C. g_update_kernel
- D. vi
Answer: B
NEW QUESTION # 28
What is the Iterator process?
- A. Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance failure
- B. Iterator is the process that follow Appliance recovery and simulates what was a distribution if recovered Appliance was alive
- C. Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance recovery
- D. Iterator is the process that simulates distribution in case of Appliance failure
Answer: A
NEW QUESTION # 29
What is the minimal amount of cables needed in order to connect an Appliance to an Orchestrator?
- A. Four cables: uplink, downlink, SYNC and Management
- B. One Downlink cable only
- C. Two cables: one uplink and one downlink
- D. Three cables: uplink, downlink, SYNC
Answer: B
NEW QUESTION # 30
Which setting is required in order to connect an appliance with 40Gbps downlink interface and DAC to the Orchestrator MHO-140?
- A. No change required
- B. On Orchestrator: Change port type from uplink to downlink
- C. On Orchestrator: Change QSFP mode from 100Gbps to 40Gbps
- D. On Appliance: Change a port speed to 10Gbps
Answer: B
NEW QUESTION # 31
What is the minimal requirement for a Security Group?
- A. None, it may be empty.
- B. 1 Appliance and 1 administrator with Multi-Domain admin permissions
- C. 2 Appliances and 2 ports
- D. 1 Appliance and 1 management port
Answer: D
NEW QUESTION # 32
What kind of cluster Dual-Site can be compared to?
- A. Active-Active
- B. Active-Standby only
- C. VSLS only
- D. Active-Standby or VSLS
Answer: D
Explanation:
A Dual-Site cluster is a type of cluster that combines the features of both Active-Standby and VSLS (Virtual Systems Load Sharing) clusters. Dual-Site clusters allow you to have two active clusters, one at each site, and the traffic is distributed between the two sites based on predefined rules and priorities.
A Dual-Site cluster can be compared to an Active-Standby cluster because one of the clusters is running in a passive mode and is only activated in case of a failure or a planned maintenance of the active cluster. And also can be compared to a VSLS cluster because both clusters are active and share the traffic load.
It's a type of High Availability solution that provides redundancy and failover capabilities across two geographically separated sites. In case of a failure or a outage on one site, the traffic is automatically redirected to the other site, ensuring that the service is not interrupted.
NEW QUESTION # 33
What is the default range of physical ports for downlinks on Orchestrator MHO-170?
- A. 3 - 16
- B. 1 - 16
- C. 17 - 31
- D. 25 - 32
Answer: C
NEW QUESTION # 34
......
100% Free 156-835 Daily Practice Exam With 66 Questions: https://www.actual4exams.com/156-835-valid-dump.html
Pass 156-835 Review Guide, Reliable 156-835 Test Engine: https://drive.google.com/open?id=1G-l0Db4cnmoWDpdEf8JlwcDQQfPPSQon