Exam Questions Answers Braindumps NS0-183 Exam Dumps PDF Questions
Download Free Network Appliance NS0-183 Real Exam Questions
NEW QUESTION 29
Before starting a base installation on an AFF A400, you need to find out the default cluster interconnect ports for the AFF A400 controllers.
In this scenario, which three resources would you use to find this information? (Choose three.)
- A. AFF FAS Documentation Center
- B. Active IQ Unified Manager
- C. Interoperability Matrix Tool (IMT)
- D. hardware installation setup poster
- E. Hardware Universe (HWU)
Answer: A,D,E
NEW QUESTION 30
You are installing a new AFF A400 cluster for a customer. The customer indicates that they want to take advantage of AutoSupport On Demand.
In this scenario, which AutoSupport transport protocol must you use?
- A. SMTP
- B. HTTPS
- C. FTP
- D. HTTP
Answer: B
Explanation:
Explanation/Reference: https://www.netapp.com/media/10438-tr-4444.pdf (9)
NEW QUESTION 31
Click the Exhibit button.
Your ONTAP cluster shows the cluster network errors that are shown in the event log.
What is used by ONTAP software to log the errors that are shown in the exhibit?
- A. BGP
- B. EMS
- C. AutoSupport
- D. SNMP
Answer: B
NEW QUESTION 32
When completing a new ONTAP 9.5 cluster base installation, which three SVM types will be present on the system by default? (Choose three.)
- A. system SVM
- B. cluster SVM
- C. admin SVM
- D. node SVM
- E. data SVM
Answer: A,C,D
NEW QUESTION 33
After performing a controller upgrade on an HA pair in an ONTAP 9.5 cluster, you want to decommission the old systems.
Which statement is correct in this scenario?
- A. The systems do not need to be decommissioned because the serial numbers are overtaken by the new systems.
- B. Decommissioning is done automatically when the systems no longer send AutoSupport messages.
- C. Open a Priority 1 technical case with NetApp Global Support and specify "Decommission" in the title.
- D. Ask the customer to log in to http://mysupport.netapp.com and decommission the old systems.
Answer: D
NEW QUESTION 34
Click the Exhibit button.
Referring to the exhibit, what information is forwarded to syslog after you enter the scripted install commands? (Choose two.)
- A. command history
- B. AutoSupport messages
- C. SNMP traps
- D. EMS messages
Answer: A,B
NEW QUESTION 35
Click the Exhibit button.
You plan to install a new ONTAP cluster at a customer site by using the new ONTAP System Manager 9.7 GUI.
Referring to the exhibit, what must you do before you provision initial storage?
- A. Configure protocols.
- B. Configure a remote tier.
- C. Configure aggregates.
- D. Configure cluster LIFs.
Answer: C
NEW QUESTION 36
Click the Exhibit button.
Your ONTAP cluster shows the cluster network errors that are shown in the event log. What is used by ONTAP software to log the errors that are shown in the exhibit?
- A. BGP
- B. EMS
- C. AutoSupport
- D. SNMP
Answer: B
NEW QUESTION 37
Which statement about LIFs is true?
- A. A data LIF can be associated with multiple SVMs.
- B. One cluster-management LIF exists per node.
- C. Cluster LIFs and data LIFs can share a port.
- D. One port can host multiple data LIFs.
Answer: D
NEW QUESTION 38
After completing the installation of a DS224C shelf, you observe the error shown in the exhibit.
Which action should you take to troubleshoot the error? (Choose two.)
- A. Perform a takeover-giveback.
- B. Re-seat the SAS card.
- C. Re-seat the IOM module.
- D. Reconnect the SAS cable.
Answer: C,D
NEW QUESTION 39
Which two commands verify that AutoSupport is working as expected?
- A. autosupport check show
- B. autosupport history show
- C. autosupport test show
- D. autosupport show
Answer: A,B
NEW QUESTION 40
Which NetApp tool should you use to set up an ONTAP 9.5 cluster?
- A. SANtricity Storage Manager
- B. Config Advisor
- C. OnCommand System Manager
- D. System Setup
Answer: B
NEW QUESTION 41
You are installing a new ONTAP 9.7 cluster and attaching the cluster to two separate networks. Your customer has indicated that the same range of client IP addresses are used on both networks and that the networks are never allowed to communicate with each other.
In this scenario, which ONTAP feature must be configured to securely allow all clients to access ONTAP NAS protocols?
- A. BGP
- B. IPspaces
- C. routing
- D. broadcast domains
Answer: B
Explanation:
https://www.netapp.com/media/16885-tr-4182.pdf 9.3 Multiple IPspaces with Overlapping IP Addresses
NEW QUESTION 42
You are planning to install a new ONTAP 9.7 All SAN Array (ASA) into your existing data center.
In this scenario, which cluster configuration is allowed with ASA controllers?
- A. Add the ASA controllers to an existing 10-node cluster.
- B. ASA controllers can only be added to clusters that have existing SAN licenses.
- C. ASA controllers can only be installed as a standalone HA pair.
- D. Add the ASA controllers to an existing 4-node cluster with NAS licenses.
Answer: C
Explanation:
https://docs.netapp.com/allsan/index.jsp?topic=%2Fcom.netapp.doc.dot-asa-config%2FGUID-C0C9B6EF-1AA7-429E-BB84-AC5F9E16D088.html
NEW QUESTION 43
You are installing a new ONTAP 9.7 cluster by following the installation and setup poster. You are ready to complete the initial cluster setup. You have connected your laptop to the management switch. However, when browsing the network, you are unable to discover the ONTAP controllers.
Which statement explains this behavior?
- A. You do not have network discovery enabled.
- B. You do not have a static IP address.
- C. You do not have IPv6 configuration set.
- D. You do not have a default gateway set.
Answer: D
NEW QUESTION 44
You are cabling two Cisco 3232C switches for the cluster interconnect of a 4-node AFF A800 cluster.
Which pair of ports are used to cable the Inter-Switch Link (ISL) between the switches?
- A. 0/1 and 0/2
- B. 1/31 and 1/32
- C. 1/21 to 1/24
- D. 0/13 to 0/16
Answer: B
NEW QUESTION 45
After a storage failover, you notice that a NAS LIF, that is linked to the broadcast domain CIFS, is no longer reachable after the takeover. Node cluster1-01 is still waiting for giveback.
Referring to the exhibit, what caused the problem?
- A. The broadcast-domain MTU needs to be either 1500 or 9000.
- B. The ports of cluster1-02 are missing in the broadcast domain.
- C. Port a0a of node cluster1-01 is down.
- D. The LIF has to be configured with a failover group.
Answer: A
NEW QUESTION 46
Which two NetApp features encrypt storage data? (Choose two.)
- A. NVMe
- B. NVE
- C. TPM
- D. NSE
Answer: B,D
NEW QUESTION 47
You are deploying a cluster with four AFF A300 nodes and Cisco 3232C switches. When you arrive at the customer's site, you notice that there are multiple breakout cables and four Cisco 3232C switches. In this scenario, which statement is true?
- A. Your customer ordered a MetroCluster IP configuration.
- B. A 4-node AFF A300 cluster requires two Cisco 3232C switches for the cluster interconnect and two for management.
- C. Cisco best practices require four Cisco 3232C switches for high availability.
- D. A 4-node AFF A300 cluster requires four Cisco 3232C switches.
Answer: A
NEW QUESTION 48
You are installing a new ONTAP 9.7 cluster and attaching the cluster to two separate networks. Your customer has indicated that the same range of client IP addresses are used on both networks and that the networks are never allowed to communicate with each other.
In this scenario, which ONTAP feature must be configured to securely allow all clients to access ONTAP NAS protocols?
- A. BGP
- B. IPspaces
- C. broadcast domains
- D. routing
Answer: C
Explanation:
Explanation/Reference: https://www.netapp.com/media/16885-tr-4182.pdf (9)
NEW QUESTION 49
You are planning to install a new ONTAP 9.7 All SAN Array (ASA) into your existing data center.
In this scenario, which cluster configuration is allowed with ASA controllers?
- A. Add the ASA controllers to an existing 10-node cluster.
- B. ASA controllers can only be installed as a standalone HA pair.
- C. ASA controllers can only be added to clusters that have existing SAN licenses.
- D. Add the ASA controllers to an existing 4-node cluster with NAS licenses.
Answer: C
NEW QUESTION 50
An ONTAP cluster is installed at a secure site. The array has no access to the Internet but is managed 24/7 by onsite engineers. The customer requires that when hardware failures occur, the failures are reported to the NetApp Support team as quickly as possible.
In this scenario, which two tasks should be performed during the project hand-off procedure to satisfy the customer's requirement? (Choose two.)
- A. Educate the onsite engineer about how to manually log support calls.
- B. Educate the onsite engineers about invoking the AutoSupport tool from ONTAP System Manager.
- C. Ensure that the onsite engineers receive EMS alerts when hardware issues occur.
- D. Ensure that Active IQ Config Advisor is installed.
Answer: A,C
NEW QUESTION 51
You use the system health subsystem show command to troubleshoot your newly installed ONTAP cluster.
In this scenario, which two health outputs would this command show you? (Choose two.)
- A. data switch cabling
- B. shelf connectivity
- C. cluster switch cabling
- D. node CPU utilization
Answer: B,D
NEW QUESTION 52
Which statement regarding a node-management LIF is true?
- A. The LIF can be set up on a dedicated VLAN in the cluster network.
- B. The LIF can be set only on the built-in node-management port - e0M.
- C. The LIF must use two switches for redundancy purposes.
- D. The LIF can be set up on a dedicated VLAN in the data network.
Answer: D
NEW QUESTION 53
You are installing a new AFF A400 cluster that is running ONTAP 9.7 software. You are asked to attach an Amazon S3 cloud tier for FabricPool technology.
In this scenario, which two NetApp License File (NLF) types are supported for cloud tiering? (Choose two.)
- A. term-based
- B. base
- C. perpetual
- D. master
Answer: A,C
Explanation:
http://docs.netapp.com/ontap-9/index.jsp?topic=%2Fcom.netapp.doc.dot-mgng-stor-tier-fp%2FGUID-C3C125BF-44DA-409D-9F93-B73545FB336B.html
NEW QUESTION 54
......
Latest Network Appliance NS0-183 Real Exam Dumps PDF: https://www.actual4exams.com/NS0-183-valid-dump.html