[Jan 24, 2022] Fully Updated Dumps PDF - Latest 300-410 Exam Questions and Answers
100% Free 300-410 Exam Dumps to Pass Exam Easily from Actual4Exams
The Cisco 300-410 exam is all about the implementation of Cisco enterprise advanced routing and services. It also evaluates one’s knowledge and skills in troubleshooting routing services and technologies, infrastructure security, infrastructure automation, infrastructure services, VPN services, and Layer 3.
NEW QUESTION 120
Refer to the exhibit.
Which interface configuration must be configured on the space A route enable a dynamic DMVPN tunnel with the spoke B router?
A)
B)
C)
D)
- A. Option B
- B. Option C
- C. Option A
- D. Option D
Answer: D
NEW QUESTION 121
Refer to the exhibit.
While troubleshooting an EIGRP neighbor adjacency problem, the network engineer notices that the interface connected to the neighboring router is not participating in the EIGRP process. Which action resolves the issues?
- A. Configure EIGRP metrics on interface FastEthernet0/3
- B. Configure the network command under EIGRP address family vrf CLIENT1
- C. Configure the network command under EIGRP address family ipv4
- D. Configure the network command to network 172.16.0.1 0.0.0.0
Answer: B
NEW QUESTION 122
Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?
- A. shared risk link group-disjoint
- B. lowest-repair-path-metric
- C. linecard-disjoint
- D. interface-disjoint
Answer: C
NEW QUESTION 123
Refer to the exhibit. An administrator noticed that after a change was made on R1, the timestamps on the system logs did not match the clock.
What is the reason for this error?
- A. The system clock is set incorrectly to summer-time hours.
- B. The NTP server is in a different time zone.
- C. The keyword localtime is not defined on the timestamp service command.
- D. An authentication error with the NTP server results in an incorrect timestamp.
Answer: D
Explanation:
Section: Infrastructure Services
NEW QUESTION 124
An engineer is trying to copy an IOS file from one router to another router by using TFTP. Which two actions are needed to allow the file to copy? (Choose two.)
- A. Copy the file to the destination router with the copy tftp: flash: command
- B. TFTP is not supported in recent IOS versions, so an alternative method must be used
- C. Configure the TFTP authentication on the source router with the tftp-server authentication local command
- D. Enable the TFTP server on the source router with the tftp-server flash: <filename> command
- E. Configure a user on the source router with the username tftp password tftp command
Answer: A,D
NEW QUESTION 125
Refer to the exhibit. An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?
- A. Use an extended access list instead of a standard access list.
- B. Change sequence 10 in the route-map command from permit to deny.
- C. Add this statement to the route map: route-map RM-OSPF-DL deny 20.
- D. Use a prefix list instead of an access list in the route map.
Answer: D
Explanation:
Section: Layer 3 Technologies
NEW QUESTION 126
Refer to the exhibit.
What is the result of applying this configuration?
- A. The router can form BGP neighborships with any other device.
- B. The router cannot form BGP neighborships with any device that is matched by the access list named
"BGP". - C. The router cannot form BGP neighborships with any other device.
- D. The router can form BGP neighborships with any device that is matched by the access list named
"BGP".
Answer: A
NEW QUESTION 127 
Refer to the exhibit. Network operations cannot read or write any configuration on the device with this configuration from the operations subnet.
Which two configurations fix the issue? (Choose two.)
- A. Modify access list 1 and allow SNMP in the access list.
- B. Configure SNMP rw permission in addition to community ciscotest.
- C. Modify access list 1 and allow operations subnet in the access list.
- D. Configure SNMP rw permission in addition to community ciscotest 1.
- E. Configure SNMP rw permission in addition to version 1.
Answer: B,C
Explanation:
Section: Infrastructure Services
NEW QUESTION 128
Refer to the exhibit.
An IP SLA is configured to use the backup default route when the primary is down, but it is not working as desired. Which command fixes the issue?
- A. R1(config)# ip route 0.0.0.0.0.0.0.0.1.1.1.1 track 1
- B. R1(config)#ip sla track 1
- C. R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2 10 track 1
- D. R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2
Answer: A
Explanation:
Reference:
Note: By default Static Router AD value-1 hence ip route 0.0.0.0. 0.0.0.0. 1.1.1.1 track 1 means AD-1 which must be less than of back up route AD.
Define the backup route to use when the tracked object is unavailable. !--- The administrative distance of the backup route must be greater than !--- the administrative distance of the tracked route. !--- If the primary gateway is unreachable, that route is removed !--- and the backup route is installed in the routing table !--- instead of the tracked route.
https://www.cisco.com/c/en/us/support/docs/ip/ip-routing/200785-ISP-Failover-with-default-routes-using-I.html
https://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/118962-configure-asa-00.html
NEW QUESTION 129
What statement about route distinguishes in an MPLS network is true?
- A. Route distinguishes are used for label bindings
- B. Route distinguishers allow multiple instances of a routing table to coexist within the edge router.
- C. Route distinguishes make a unique VPNv4 address across the MPLS network.
- D. Route distinguishes define which prefixes are imported and exported on the edge router
Answer: C
NEW QUESTION 130
An engineer is configuring a network and needs packets to be forwarded to an interface for any destination address that is not in the routing table. What should be configured to accomplish this task?
- A. set ip next-hop verify-availability
- B. set ip next-hop recursive
- C. set ip next-hop
- D. set ip default next-hop
Answer: D
Explanation:
NEW QUESTION 131
Refer to the exhibit. What is the result of applying this configuration?
- A. The router can form BGP neighborships with any other device.
- B. The router cannot form BGP neighborships with any device that is matched by the access list named
"BGP". - C. The router cannot form BGP neighborships with any other device.
- D. The router can form BGP neighborships with any device that is matched by the access list named "BGP".
Answer: A
Explanation:
Section: Layer 3 Technologies
NEW QUESTION 132
Refer to the exhibit.
The network administrator configured VRF lite for customer A. The technician at the remote site misconfigured VRF on the router. Which configuration will resolve connectivity for both sites of customer a?
- A. Option B
- B. Option C
- C. Option A
- D. Option D
Answer: D
Explanation:
Explanation
From the exhibit, we learned:
+ VRF customer_a was exported with Route target (RT) of 1:1 so at the remote site it must be imported with the same RT 1:1.
+ VRF customer_a was imported with Route target (RT) of 1:1 so at the remote site it must be exported with the same RT 1:1.
Therefore at the remote site we must configure the command "route-target both 1:1" (which is equivalent to two commands "route-target import 1:1" & "route-target export 1:1".
NEW QUESTION 133
Refer to the exhibits. An engineer filtered messages based on severity to minimize log messages. After applying the filter, the engineer noticed that it filtered required messages as well. Which action must the engineer take to resolve the issue?
- A. Configure syslog level 5.
- B. Configure syslog level 3.
- C. Configure syslog level 2.
- D. Configure syslog level 4.
Answer: B
NEW QUESTION 134
A network engineer is investigating a flapping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output does not show the time of the flap.
Which command allows on the switch the time of the flap according to the clock on the device?
- A. clock summer-time mst recurring 2 Sunday mar 2:00 1 sunday nov 2:00
- B. service timestamps log uptime
- C. service timtstamps log datetime localtime show-timezone
- D. clock calendar-valid
Answer: C
NEW QUESTION 135
Drag and Drop Question
Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.
Answer:
Explanation:
NEW QUESTION 136
R2 has a locally originated prefix 192.168.130.0/24 and has these configurations:
What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the neighbor 1.1.1.1 route-map OUT out command?
- A. Network 192.168.130.0/24 is not allowed in the R1 table
- B. R1 does not accept any routes other than 192.168.130.0/24
- C. R1 sees 192.168.130.0/24 as two AS hops away instead of one AS hop away.
- D. R1 does not forward traffic that is destined for 192.168.30.0/24
Answer: C
Explanation:
Section: Layer 3 Technologies
NEW QUESTION 137
Drag and drop the MPLS VPN device types from me left onto the definitions on the right.
Answer:
Explanation:
NEW QUESTION 138
Refer to the exhibit.
A company is evaluating multiple network management system tools. Trending graphs generated by SNMP data are returned by the NMS and appear to have multiple gaps. While troubleshooting the issue, an engineer noticed the relevant output. What solves the gaps in the graphs?
- A. Remove the exceed-rate command in the class map.
- B. Configure the CIR rate to a lower value that accommodates all the NMS tools
- C. Separate the NMS class map in multiple class maps based on the specific protocols with appropriate CoPP actions
- D. Remove the class map NMS from being part of control plane policing.
Answer: C
NEW QUESTION 139
Refer to the exhibit.
The output of the trace route from R5 shows a loop in the network. Which configuration prevents this loop?
A)
B)
C)
D)
- A. Option A
- B. Option B
- C. Option D
- D. Option C
Answer: A
NEW QUESTION 140
Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.
Answer:
Explanation:
This state specifies that the router has received a hello packet from its neighbor, but the receiving router's ID was not included in the hello packet. When a router receives a hello packet from a neighbor, it should list the sender's router ID in its hello packet as an acknowledgment that it received a valid hello packet.
2-Way
Reference:
+ Each router compares the DBD packets that were received from the other router: Exchange
+ Routers exchange information with other routers in the multiaccess network: Exstart
+ The neighboring router requests the other routers to send missing entries: Loading
+ The network has already elected a DR and a backup BDR: 2-way
+ The OSPF router ID of the receiving router was not contained in the hello message: Init
+ No hellos have been received from a neighbor router: Down
When OSPF adjacency is formed, a router goes through several state changes before it becomes fully adjacent with its neighbor. The states are Down -> Attempt (optional) -> Init -> 2-Way -> Exstart -> Exchange -> Loading -> Full. Short descriptions about these states are listed below:
Down: no information (hellos) has been received from this neighbor.
Attempt: only valid for manually configured neighbors in an NBMA environment. In Attempt state, the router sends unicast hello packets every poll interval to the neighbor, from which hellos have not been received within the dead interval.
Init: specifies that the router has received a hello packet from its neighbor, but the receiving router's ID was not included in the hello packet
2-Way: indicates bi-directional communication has been established between two routers.
Exstart: Once the DR and BDR are elected, the actual process of exchanging link state information can start between the routers and their DR and BDR.
Exchange: OSPF routers exchange and compare database descriptor (DBD) packets Loading: In this state, the actual exchange of link state information occurs. Outdated or missing entries are also requested to be resent.
Full: routers are fully adjacent with each other
(Reference: http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080093f0e.shtml)
NEW QUESTION 141
Refer to the exhibit.
An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 loses reachability with the router R3 Fa0/0 interface. The route has changed to flow through router R2. Which debug command is used to troubleshoot this issue?
- A. debug ip routing
- B. debug ip packet
- C. debug ip flow
- D. debug ip sla error
Answer: A
Explanation:
Explanation
debug ip routing This command enables debugging messages related to the routing table.
NEW QUESTION 142
......
Free 300-410 Exam Questions 300-410 Actual Free Exam Questions: https://www.actual4exams.com/300-410-valid-dump.html
Verified 300-410 dumps and 240 unique questions: https://drive.google.com/open?id=1mKeKpHbno651ug6qg44OHTRYnqgYV_rF