Dec-2023 HP HPE6-A45 Actual Questions and 100% Cover Real Exam Questions
HPE6-A45 Free Exam Questions and Answers PDF Updated on Dec-2023
Preparing for the HPE6-A45 exam requires a strong understanding of Aruba switching technologies, as well as experience in deploying and managing Aruba switching solutions. Candidates can take advantage of a variety of resources, including study guides, practice exams, and training courses offered by Aruba and its partners. By passing the HPE6-A45 exam and obtaining the ACSP certification, IT professionals can demonstrate their expertise in Aruba switching technologies and enhance their career opportunities in the IT industry.
HP HPE6-A45 Certification Exam is an important certification for professionals who want to specialize in Aruba switching solutions. Aruba Certified Switching Professional Exam certification is ideal for network administrators, network engineers, and network architects who want to gain a deeper understanding of Aruba switching technologies. By passing HPE6-A45 exam, you will demonstrate that you have the necessary skills to configure and troubleshoot complex Aruba switching solutions, which can help you advance your career and increase your earning potential.
HP HPE6-A45 exam is a computer-based test that consists of 60 multiple-choice questions. Candidates have 90 minutes to complete the exam, and they must achieve a passing score of at least 75% to earn the certification. HPE6-A45 exam is available in English and Japanese, and candidates can take it at any Pearson VUE testing center around the world.
NEW QUESTION # 65
Refer to the exhibit.
The access layer AOS-Switches currently run DHCP snooping on VLAN 2 and connection rate filtering on edge ports. They are at default settings for ARP protection. A network administrator then enters these commands on each of the access layer switches:
Switch(config)# arp-protect vlan 2 Switch(config)# arp-protect
Which behavior accurse?
- A. The switches can now prevent ARP poisoning attacks and do not interfere with legitimate communications.
- B. The switches will not apply ARP protection due to interference from DHCP snooping, so the commands have no effect on current behavior.
- C. The switches will forward legitimate traffic and prevent ARP poisoning attacks, but interfere with connection rate filtering.
- D. The switches can prevent ARP poisoning attacks, but legitimate communications with VLAN 2 could also be disrupted.
Answer: A
NEW QUESTION # 66
Refer to the exhibit.
An AOS-Switch has the ACL shown in the exhibit. A network administrator then enters these commands:
Switch(config)# mac-access-list standard myACL
Switch(config-std-macl)# deny 007d.45cc.0000 0000.0000.ffff
How does this ACL treat these frames:
1 = 007d.45cc.ffff 2 = 007d.45cc.0000
- A. It denies both frames.
- B. It permits both frames.
- C. It denies frame 1 and permits frame 2.
- D. It permits frame 1 and denies frame 2.
Answer: C
NEW QUESTION # 67
A network administrator configures VSF settings on two Aruba 2930F switches. The switches form two separate VSF fabrics. What should the administrator check?
- A. that each switch is assigned a unique VSF priority
- B. that LLDP MAD is configured on both members
- C. that the domain ID matches on both switches
- D. that the switch with the lower priority has the lower member ID
Answer: C
NEW QUESTION # 68
Refer to the exhibit.
AOS-Switches will enforce 802.1X authentication on edge ports. The company has two RADIUS servers, which are meant to provide redundancy and load sharing of requests. The exhibit shows the planned RADIUS setting to deploy to the switches.
Which adjustment to the plan should administrators make in order to meet the customers' requirements?
- A. Change the order in which the RADIUS servers are specified on half of the switches.
- B. Remove the dynamic authorization setting for both RADIUS servers.
- C. Specify one server on half of the switches and the other server on the other half of the switches.
- D. Specify a different RADIUS dynamic authorization port for each of the RADIUS servers.
Answer: A
NEW QUESTION # 69
Refer to the exhibit.
A network administrator needs to alter myACL so that it permits all traffic that arrives in VLAN 2 and is destined to 10.1.10.0/24. Besides this change, the ACL must continue to act as it does now. The administrator plans this new rule:
permit ip any 10.1.10.0/24
- A. Apply the new rule without a rule ID to ensure that the switch applies the automatic processing order to it.
- B. Remove the ACL from the VLAN and re-apply it as an inbound VLAN ACL (VACL). Then, add the new rule with any ID higher than 2.
- C. Enable ACL grouping on the switch. Add the new rule in anew ACL. Then, group the new ACL with myACL.
- D. Resequence the ACL with more space, then add the new rule with a sequence ID before the ID for the current third rule.
Answer: D
Explanation:
Explanation/Reference:
NEW QUESTION # 70
Refer to the exhibit.
Endpoints in VLAN 2 connect directly to this switch. These devices should only be able to send DHCP, DNS, HTTP, and HTTPS traffic. However, they are able to send any traffic. Based on the exhibit, what is the issue?
- A. The ACL lacks a deny ip any any statement at the end.
- B. The name of the ACL applied to VLAN 2 is incorrect.
- C. The ACL is applied in the wrong direction.
- D. The switch does not have an IP address on VLAN 2.
Answer: B
NEW QUESTION # 71
Refer to the exhibits.
Exhibit 1
Exhibit 2
Switch-1 and Switch-2 lost IP connectivity with each other. They did not detect the issue for several seconds and caused a temporary traffic disruption. The administrations expected failover to the backup route through Switch-3 to occur in less than a second. The administrators restore the failed link and view the output on Switch-1, shown in the exhibit.
What should they do to create the expected behavior if connectivity is lost again?
- A. Set a BFD echo source IP address on each OSPF routing switch in VLAN 100
- B. Manually configure the network type as point-to-point on each OPSF routing switch in VLAN 100
- C. Enable BFD in asynchronous mode on each OSPF routing switch in VLAN 100
- D. Lower the hello timer to a given range of times on each OSPF routing switch in VLAN 100
Answer: C
NEW QUESTION # 72
Refer to the exhibits.
Exhibit 1
Exhibit 2
In the exhibits, VLAN 20 under a device name indicates that the device is configured with that VLAN. The exhibits also indicate whether VLAN 20 is statically configured on each link, either as an untagged or a tagged VLAN. If the link has no label, VLAN 20 is not statically configured on that link.
A network administrator needs to deploy AOS-Switches that use port-based tunneled node. The plan calls for tunneled-node endpoints to be assigned to VLAN 20 and for the Aruba Mobility Controller to handle the tunneled-node traffic at Layer 2. Which exhibit shows the correct plan for VLAN 20 in the wired infrastructure?
- A. C
- B. D
- C. B
- D. A
Answer: C
NEW QUESTION # 73
A network administrator needs to set up an AOS-Switch to use port-based tunneled node for connected devices.
However, the administrator wants the switch to forward traffic without tunneling if it cannot reach a tunneled-node server.
What should the administrator do?
- A. Configure a local switching profile on the Mobility Controller that acts as tunneled-node server.
- B. Apply the tunneled-node profile to ports, and set the local-switching-fallback option.
- C. Make sure that the switch has an IP address on the untagged VLAN assigned to the ports.
- D. Set the switch to role-based tunneled node, and make sure it uses the default initial user role.
Answer: D
NEW QUESTION # 74
Refer to the exhibit.
The company wants the fastest convergence and best load sharing of traffic over the links between Switch-1 and the VSF fabric. Which technology should the network administrator implement on these links?
- A. LACP
- B. MSTP
- C. loop protection
- D. RPVST+
Answer: A
NEW QUESTION # 75
Refer to the exhibits.
Exhibit 1
Exhibit 2
The exhibits show the current operational state for routes on Switch-3. The company wants Switch-3 to send all traffic to 172.16.0.0/16 through Switch-2.
Which single configuration change creates the desired behavior?
- A. Change the OSPF external metric type to 2 on Switch-1 and Switch-2.
- B. Change the OSPF external metric type to 1 on Switch-1 and Switch-3.
- C. Set a cost of 15 in the redistribute static command on Switch-2.
- D. Set a cost of 5 in the router ospf area 0.0.0.1 stub command on Switch-1.
Answer: D
NEW QUESTION # 76
The security plan for AOS-Switches requires protection from incoming malware traffic: generated from a worm-or virus-infected host.
Which feature should be implemented to provide the required protection?
- A. proxy ARP
- B. port security
- C. connection-rate filtering
- D. DHCP snooping
Answer: C
Explanation:
Explanation/Reference:
Reference: http://h22208.www2.hpe.com/eginfolib/networking/docs/switches/K-KA-KB/15-18/5998-
8150_access_security_guide/content/s_about_connection-rate_filtering.html
NEW QUESTION # 77
Refer to the exhibit.
Switch-1 is an AOS-switch that is operating at factory default settings for QoS and has type of service disabled. It receives a frame with 802.1p value 5 on trk1, on VLAN 2. How does the switch treat the frame when it forwards it on TRK2?
- A. It forwards it with normal priority and 802.1p 5
- B. It forwards it with higher than normal priority and 802.1p 5.
- C. It forwards it with higher than normal priority and 802.1p 0.
- D. It forwards it with normal priority and 802.1p 0.
Answer: A
NEW QUESTION # 78
Refer to the exhibit.
Which issue needs to be addressed in this design?
- A. a new way to provide core redundancy, because AOS-Switches in VSF fabrics can only establish BGP relationships with AOS-Switches
- B. a way to ensure that the company private network does not become a transit for traffic between ISP 1 and ISP 2
- C. an adjustment to the physical links, because both links to the ISP routers must be on the commander to prevent a split-brain situation
- D. a new plan for ISP redundancy, because Switch-1 can only support one AS number, so it cannot connect to both ISP 1 and ISP 2
Answer: B
NEW QUESTION # 79
Refer to the exhibits.
Exhibit 1.
Exhibit 2.
The VoIP phone connects, authenticates successfully, and is dynamically assigned to tagged VLAN 6. The endpoint connected to the phone does not authenticate but starts to send untagged traffic.
How does the switch handle this traffic?
- A. It relays the traffic to the RADIUS server for authentication.
- B. It drops the traffic.
- C. It forwards the traffic in VLAN 6.
- D. It forwards the traffic in VLAN 5.
Answer: A
NEW QUESTION # 80
......
HP HPE6-A45 Real 2023 Braindumps Mock Exam Dumps: https://www.actual4exams.com/HPE6-A45-valid-dump.html