The Best HPE6-A45 Exam Study Material and Preparation Test Question Dumps
Get Ready to Pass the HPE6-A45 exam Right Now Using Our Aruba Certified Switching Professional (ACSP) V1 Exam Package
NEW QUESTION # 29
Refer to the exhibits.
Exhibit 1
Exhibit 2
Switch-1(config)# spanning-tree
Switch-1(config)# spanning-tree config-name "exam"
Switch-1(config)# spanning-tree instance 1 vlan 10-19
Switch-1(config)# spanning-tree instance 2 vlan 20-29
Switch-2(config)# spanning-tree
Switch-2(config)# spanning-tree config-name "exam"
Switch-2(config)# spanning-tree instance 1 vlan 10-19
Switch-2(config)# spanning-tree instance 2 vlan 20-29
Switch-2(config)# spanning-tree priority 0
Switch-2(config)# spanning-tree instance 1 priority 0
Switch-2(config)# spanning-tree instance 2 priority 1
Switch-3(config)# spanning-tree
Switch-3(config)# spanning-tree config-name "exam"
Switch-3(config)# spanning-tree instance 1 vlan 10-19
Switch-3(config)# spanning-tree instance 2 vlan 20-29
Switch-3(config)# spanning-tree priority 1
Switch-3(config)# spanning-tree instance 1 priority 1
Switch-3(config)# spanning-tree instance 2 priority 0
Switch-4(config)# spanning-tree
Switch-4(config)# spanning-tree config-name "exam"
Switch-4(config)# spanning-tree instance 1 vlan 10-19
Switch-4(config)# spanning-tree instance 2 vlan 20-29
The network administrator enters the commands shown in Exhibit 2. What is the spanning tree status on A1 and A2?
- A. Both A1 and A2 forward traffic.
- B. Both A1 and A2 block traffic.
- C. A1 forwards traffic, and A2 blocks traffic.
- D. A1 blocks traffic, and A2 forwards traffic.
Answer: C
NEW QUESTION # 30
Refer to the exhibit.
A network administrator wants to add the protections of root guard to the network. Based on the spanning tree topology, on which ports should the network administrator implement root guard?
- A. 2 and A3
- B. 1 and 2
- C. 3-24
- D. A1 and A2
Answer: D
NEW QUESTION # 31
Exhibit
The network administrator wants to summarize routes as much as possible in between areas. What is the correct range to specify for the router OSPF Area 2 command on Switch-2?
- A. 10.0.0.0/20
- B. 10.0.0.0/21
- C. 10.0.16.0/21
- D. 10.0.8.0/21
Answer: C
NEW QUESTION # 32
Refer to the exhibit.
An administrator created a backplane stack with the plug-and-play method and did not after the default backplane stacking settings. Later, who backplane stacking links failed as shown in the exhibit. The network administrator then restored the failed links.
When the stack is reformed, which switches become commander and standby?
- A. Member 1 becomes commander, and Member 2 becomes standby
- B. Member 4 remains commander, and Member 1 becomes standby
- C. Member 4 remains commander, and Member 5 remains standby
- D. Member 1 becomes commander, and Member 4 becomes standby
Answer: B
NEW QUESTION # 33
Refer to the exhibits.
Exhibit 1
Exhibit 2
Exhibit 1 shows a portion of the BGP routing table when the BGP solution was first deployed. Exhibit 2 shows the same portion at the current time. What can explain the current state?
- A. An administrator has applied a route map on Switch-1 that filters advertised routes.
- B. Due to changes at ISP 1, Switch-1 now selects a different best route.
- C. Switch-1 can no longer reach ISP 1 at 192.168.1.1.
- D. Due to changes in the private network, Switch-1 can no longer reach 192.168.2.1.
Answer: B
NEW QUESTION # 34
Refer to the exhibit.
The network administrator wants to summarize routes as much as possible in between areas. What is the correct range to specify for the router OSPF Area 2 command on Switch-2?
- A. 10.0.0.0/20
- B. 10.0.0.0/21
- C. 10.0.16.0/21
- D. 10.0.8.0/21
Answer: C
NEW QUESTION # 35
Refer to the exhibit.
The routing switches shown in the exhibit use OSPF, and all of their interfaces are in Area 1. A faulty link on Switch-1 went up and down many times over the course of several hours. This caused link state updates (LSUs) to flood all of the routing devices in the OSPF AS and reduce performance. The network administrator fixed the faulty link on Switch-1, but the administrator also wants to mitigate the effects if a similar issue occurs in the future.
Which design improvement would help?
- A. Divide the AS into different areas, and configure the backbone area as an NSSA
- B. Divide the AS into different areas, and aggregate routes between them
- C. Decrease the LSA generation timer, and make sure to set the same value on all routers
- D. Configure Area 1 as a stub area on all routers except Switch-2, Switch-3, and Switch-4
Answer: B
NEW QUESTION # 36
Refer to the exhibit.
An AOS-Switch has the ACL shown in the exhibit. A network administrator then enters these commands:
Switch(config)# mac-access-list standard myACL
Switch(config-std-macl)# deny 007d.45cc.0000 0000.0000.ffff
How does this ACL treat these frames:
1 = 007d.45cc.ffff 2 = 007d.45cc.0000
- A. It denies frame 1 and permits frame 2.
- B. It permits frame 1 and denies frame 2.
- C. It denies both frames.
- D. It permits both frames.
Answer: A
NEW QUESTION # 37
Refer to the exhibits.
Exhibit 1.
Exhibit 2.
The VoIP phone connects, authenticates successfully, and is dynamically assigned to tagged VLAN 6. The endpoint connected to the phone does not authenticate but starts to send untagged traffic.
How does the switch handle this traffic?
- A. It forwards the traffic in VLAN 5.
- B. It forwards the traffic in VLAN 6.
- C. It relays the traffic to the RADIUS server for authentication.
- D. It drops the traffic.
Answer: C
NEW QUESTION # 38
Refer to the exhibit.
A company has IP phones that are LLDP-MED capable. The exhibit shows the configuration for the VLAN to which IP phones belong, as well as the configuration for ports to which phones will connect. AOS-Switches at the access layer are set up to use LLDP-MED. The administrator wants to automatically provision the phones to send traffic with the right VLAN tag and priority.
Which additional configuration step must the administrator complete?
- A. Enable 802.1X and MAC-based VLANs on the ports
- B. Enable LMA and configure the proper LMA profiles
- C. Specify the voice setting in VLAN 3
- D. Specify LLDP-MED as the global LLDP mode
Answer: C
NEW QUESTION # 39
Exhibit
The network administrator configures the commands shown in Exhibit 2. Which mismatch will cause an issue?
- A. The mismatch between the key IDs specified in chain 10 and chain 11 on Switch-1
- B. The mismatch between the key-strings in the chains for VLAN 10 and VLAN 11 on Switch-1
- C. The mismatch between the key-strings associated with VLAN 10 on Switch-1 and on Switch-2
- D. The mismatch between the chain names associated with VLAN 11 on Switch-1 and on Switch-3
Answer: B
NEW QUESTION # 40
Refer to the exhibit.
A company has IP phones that are LLDP-MED capable. The exhibit shows the configuration for the VLAN to which IP phones belong, as well as the configuration for ports to which phones will connect. AOS-Switches at the access layer are set up to use LLDP-MED. The administrator wants to automatically provision the phones to send traffic with the right VLAN tag and priority.
Which additional configuration step must the administrator complete?
- A. Enable 802.1X and MAC-based VLANs on the ports
- B. Enable LMA and configure the proper LMA profiles
- C. Specify the voice setting in VLAN 3
- D. Specify LLDP-MED as the global LLDP mode
Answer: C
NEW QUESTION # 41
Refer to the exhibits.
Exhibit 1
Exhibit 2
Switch-1 has a power issue that causes it to fail. When Switch-1 comes back up, endpoints lose connectivity for a few minutes. The network administrator decides to enter this command on Switch-1:
Switch-1 (config)# vlan 10 vrrp vrid 10 preempt-delay-time 120
Exhibit 2 shows the VRRP configuration just after the change. What is the effect of this change?
- A. Switch-1 now waits to take over as Master if it fails and recovers. This should prevent the connectivity issue from occurring again.
- B. Switch-1 experiences an internal error in the VRRP process. This error causes Switch-2 to take over as Master for VLAN 2.
- C. Switch-1 and Switch-2 both become Master in their own VRRP virtual router due to the delay timer mismatch. The mismatch must be fixed.
- D. Switch-1 continues to act as it did before the preempt delay time was set. Administrators must plan additional changes to fix the issue.
Answer: B
NEW QUESTION # 42
Refer to the exhibits
Exhibit 1
Exhibit 2
Both Switch-1 and Switch-2 have an OSPF inter-area route to 10.2.0.0/16 with metric 10 in their IP routing table. Switch-3 has the default setting for ECMP. Based on the exhibits, what should the Switch-3 routing table display if the network operates as normal?
- A. no route to 10.2.0.0/16
- B. a route to 10.2.0.0/16 through 10.1.0.1
- C. a route to 10.2.0.0/16 through 10.1.0.5
- D. two routes to 10.2.0.0/16 through both 10.1.0.1 and 10.1.0.5
Answer: A
NEW QUESTION # 43
A customer wants to authenticate AOS-Switch managers to a RADIUS server. The CIO wants to assign different rights to different management users for granular control over their rights and privileges. What must the network administrator enable on the AOS-Switches to ensure they comply with this plan?
- A. a manager and operator password
- B. authentication login privileges
- C. SNMPv3 and SNMPv3 restricted access.
- D. RADIUS-based command authorization
Answer: B
NEW QUESTION # 44
An AOS-Switch needs to be configured to support tunneled node in role-based mode. The Mobility Controller administrators tell the switch administrators that the AOS-Switch will integrate with a cluster of Mobility Controllers. The cluster virtual IP address is 10.1.1.10.
How should switch administrator integrate the AOS-Switch with the cluster?
- A. Double-check the settings with the Mobility Controller administrators because the planned configuration is incomplete with the switch settings.
- B. Configure the virtual IP address as the tunneled-node-server address. The switch will automatically learn controller IP addresses to which to tunnel various traffic.
- C. Configure the virtual IP address as the tunneled-node-server address, tunneled node will work, but the clustering features will not provide redundancy.
- D. Configure the virtual IP address for the primary tunneled-node-server and an actual controller IP address for the backup tunneled-node-server in order to receive redundancy.
Answer: C
NEW QUESTION # 45
A customer wants access layer switches that support routing, ACLs, backplane stacking, and Smart rate ports. The customer asks about Aruba 5400R z 12 switches.
Which Aruba Switch model would better meet the customer's requirements?
- A. 2930F
- B. 0
- C. 1
- D. 2
Answer: B
NEW QUESTION # 46
Refer to the exhibits.
Exhibit 1
Exhibit 2
The exhibits show the current operational state for routes on Switch-3. The company wants Switch-3 to send all traffic to 172.16.0.0/16 through Switch-2.
Which single configuration change creates the desired behavior?
- A. Set a cost of 5 in the router ospf area 0.0.0.1stub command on Switch-1.
- B. Set a cost of 15 in the redistribute staticcommand on Switch-2.
- C. Change the OSPF external metric type to 2 on Switch-1 and Switch-2.
- D. Change the OSPF external metric type to 1 on Switch-1 and Switch-3.
Answer: B
NEW QUESTION # 47
......
Get Special Discount Offer of HPE6-A45 Certification Exam Sample Questions and Answers: https://www.actual4exams.com/HPE6-A45-valid-dump.html