Study HIGH Quality HPE6-A72 Free Study Guides and Exams Tutorials
Download HP HPE6-A72 Exam Dumps to Pass Exam Easily
HP HPE6-A72 Exam Syllabus Topics:
Topic | Details |
---|---|
Topic 1 |
|
Topic 2 |
|
Topic 3 |
|
Topic 4 |
|
Topic 5 |
|
Topic 6 |
|
Topic 7 |
|
Topic 8 |
|
NEW QUESTION 42
What are two OSPF attributes within the hello messages that must match to successfully establish neighbor relationships? (Choose two.)
- A. Priority
- B. Process ID
- C. Router ID
- D. Area ID
- E. Hello and Dead intervals
Answer: D,E
NEW QUESTION 43
Match the term to the correct description.
Answer:
Explanation:
NEW QUESTION 44
Click on the colored box that corresponds with the line that best represents Multicast traffic flow.
Answer:
Explanation:
Explanation:
Blue Box
NEW QUESTION 45
Place the OSI Layers in the correct order. Arrange them from least to greatest, starting with Layer 1 on the top, and progressing to Layer 7 on the bottom.
Answer:
Explanation:
1 - physical Layer
2 - Data Link Layer
3 - Network Layer
4 - Transport Layer
5 - Session Layer
6 - Presentation Layer
7 - Application Layer
NEW QUESTION 46
What is Deep Packet Inspection?
- A. a firewall process of examining the packet header all the way to Layer 7 in order to determine if the packet should be permitted or denied
- B. a machine learning method of packet inspection for the purpose of choosing which dynamic routing protocol to automatically assign
- C. a function of Policy Based Routing that examines the entire IPv4 header to forward traffic based on factors other than destination address
- D. a concept that applies to firewalls, when examining packets only up through Layer 4
Answer: A
NEW QUESTION 47
What are two mechanisms supported on AOS-CX 6300 switches used in Multi-active Detection to determine the status of the Primary member? (Choose two.)
- A. Management interface split detection
- B. BFD
- C. ARP-based
- D. Loopback keepalives
- E. Peer switch-based detection
Answer: A,C
NEW QUESTION 48
What is the correct description of a Multi-Layer Switch?
- A. multi-Layer refers specifically to using chassis switches with several line cards over stack port switches
- B. a switch with Layer 3 routing capabilities but lacks any Layer 1 features as a consequence
- C. any switch that supports PoE, LLDP-MED and Flow Control
- D. has all the functionality of a Layer 2 switch and most of the functionality of a Layer 3 router
Answer: D
NEW QUESTION 49
What is the Link Layer Discovery Protocol?
- A. a standardized protocol for communicating directly-connected device information and capabilities.
- B. a discovery protocol used between Layer 3 devices to determine routes within a single autonomous system
- C. an Aruba proprietary discovery protocol supported in all Aruba switches along with Cisco Discovery Protocol or CDP
- D. a standardized IPv6 neighbor discovery protocol used to replace the ARP and broadcast mechanism used in IPv4
Answer: A
NEW QUESTION 50
Which two port characteristics must match between LAG interfaces? (Choose two.)
- A. Chassis number
- B. Port number
- C. Duplex
- D. Member ID
- E. Media type
Answer: C,E
NEW QUESTION 51
What are two available options as part of a DHCP offer message? (Choose two.)
- A. VLANID
- B. DNS server IP
- C. SSID
- D. LLDP-MED
- E. Subnet Mask
Answer: B,E
NEW QUESTION 52
Which statement is correct regarding powering an Aruba Access Point?
- A. Using switchports for this reason is unnecessary, because Aruba Access Points typically use an AC to DC power adapter to draw power.
- B. Most administrators use PoE or PoE+ enabled switchports to provide both Ethernet connectivity and power to the AP.
- C. PoE or PoE+ enabled switchports are rarely used given concerns about causing electrical interference, with the data also carried over Ethernet cabling.
- D. PoE or PoE+ is only used with Ethernet that is carried over multi-mode fiber cabling.
Answer: B
NEW QUESTION 53
Match the available stacking feature to the correct AOS-CX switch model. Stacking features may be used more than once.
Answer:
Explanation:
NEW QUESTION 54
Refer to the exhibit.
The above command was applied to an Aruba AOS-CX 6300M 24-port switch with 4-port SFP56 uplinks. All ports are set as access switchports.
Which ports carry VLAN 1 traffic?
- A. 1/1/1-1/1/28
- B. 1/1/8-1/1/10, 1/1/5-1/1/28
- C. 1/1/8, 1/1/10, 1/1/5-1/1/24
- D. 1/1/1-1/1/24
Answer: B
NEW QUESTION 55
Match each description to the correct management tool for Aruba AOS-CX.
Answer:
Explanation:
NEW QUESTION 56
What are the benefits of a 3-Tier design over a 2-Tier? (Choose two.)
- A. Gaining the flexibility to connect the Data-Center to any Access layer switch.
- B. Lowering the cost of a deployment due to needing less switches overall.
- C. Offloading processing from the Core without routing at the Access layer.
- D. Can use lower speed links between Core to Aggregation and Aggregation to Access given the use of an Aggregation layer.
- E. Better scalability in a campus with a large number of buildings.
Answer: C,E
NEW QUESTION 57
Refer to the exhibit.
You are in the process of configuring VSF between Access-1 and Access-2. Access-1 has been configured as the VSF Master.
What is a valid configuration for Access-2 to join the VSF stack?
- A. Access-2# configure
Access-2(config)# vsf member 1 Access-2(config)# vsf renumber-to 2 Access-2(vsf-member-1)# link 2 2/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y - B. Access-2# configure
Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 2 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y - C. Access-2# configure
Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y - D. Access-2# configure
Access-2(config)# vsf member 1 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit Access-2(config)# vsf renumber-to 2
Answer: C
Explanation:
This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y
NEW QUESTION 58
Which field in the IPv4 header indicates whether the IP packet carries TCP or UDP traffic?
- A. TTL
- B. IHL
- C. Identification
- D. Protocol
Answer: D
NEW QUESTION 59
Which two options are correct regarding the IEEE 802.11ax standard? (Choose two.)
- A. is an emerging satellite connection standard to allow wireless access anywhere in the world
- B. operates in both the 2.4GHz and 5GHz radios bands
- C. operates only in the 5GHz similar to 802.11ac
- D. is the first WLAN standard to no longer use electromagnetic signals to transmit data
- E. allows transmissions of up to 4.8Gbps
Answer: B,E
Explanation:
Explanation/Reference:
NEW QUESTION 60
What is an available command on an Aruba AOS-CX switch that would back up the secondary image to a secure remote repository?
- A. copy secondary tftp://[email protected]/GL.10.04.0003.swi
- B. backup secondary sftp://[email protected]/GL.10.04.0003.swi
- C. copy sftp://[email protected]/GL.10.04.0003.swi secondary
- D. copy secondary sftp://[email protected]/GL.10.04.0003.swi
Answer: D
NEW QUESTION 61
What are two methods for remotely managing an Aruba AOS-CX switch? (Choose two.)
- A. SSH
- B. Telnet
- C. USB-C console
- D. HTTPS
- E. SNMPv2c
Answer: A,D
NEW QUESTION 62
What are two features in a 2-Tier design that are implemented at the Access layer? (Choose two.)
- A. VPN access
- B. Power over Ethernet
- C. Endpoint Access
- D. WAN/MPLS connectivity
- E. Deep packet inspection
Answer: B,C
NEW QUESTION 63
......
Get 100% Real Free Aruba Certified Switching Associate (ACSA) V1 HPE6-A72 Sample Questions: https://www.actual4exams.com/HPE6-A72-valid-dump.html
Accurate HPE6-A72 Questions with Free and Fast Updates: https://drive.google.com/open?id=1XG--cJjIQWxrrVzK_l-YyuP4oi92FUDM